Register Log In

Home Forums General Discussion Media, Shot, Beads, etc.

Page 1 of 4

1

2

3

4

		Thread Title	Replies	Views	Last Post
		Specifying mixed shot sizes by Zach 08/28/25 05:16 PM Jack Champaigne Replies: 2 Views: 2,257	2	2,257	08/28/25 05:16 PM by Jack Champaigne
		Use ASH when ASR is called out? by Dave Barkley 06/13/24 02:21 AM Walter Replies: 1 Views: 4,361	1	4,361	06/13/24 02:21 AM by Walter
		reuse of floor/leaked shot while keeping good mix by Jean Riesling 06/05/24 06:06 PM Jack Champaigne Replies: 5 Views: 9,214	5	9,214	06/05/24 06:06 PM by Jack Champaigne
		contamination of cast steel shots by 54lg 07/20/23 01:21 PM Kumar Balan Replies: 3 Views: 12,154	3	12,154	07/20/23 01:21 PM by Kumar Balan
		WPC Process by BenM 01/30/23 04:01 PM Jack Champaigne Replies: 5 Views: 10,102	5	10,102	01/30/23 04:01 PM by Jack Champaigne
		GLASS BEAD AND GLASS SHOT by donhan 07/25/22 02:07 PM Jack Champaigne Replies: 1 Views: 4,022	1	4,022	07/25/22 02:07 PM by Jack Champaigne
		NON MAG SHOT by donhan 11/24/21 05:50 PM Jack Champaigne Replies: 6 Views: 19,764	6	19,764	11/24/21 05:50 PM by Jack Champaigne
		Glass Bead for Peening by Dave Barkley 10/15/21 07:10 AM Very Old Tom Replies: 2 Views: 6,752	2	6,752	10/15/21 07:10 AM by Very Old Tom
		Magnetized media by TreyCo 03/11/21 02:00 AM wendy zhang Replies: 2 Views: 6,119	2	6,119	03/11/21 02:00 AM by wendy zhang
		Decoding Drawing Callout by RStone (again) 02/24/21 09:50 PM Walter Replies: 1 Views: 4,081	1	4,081	02/24/21 09:50 PM by Walter
		Media working environment by JAP 01/06/21 02:47 PM JAP Replies: 0 Views: 2,445	0	2,445	01/06/21 02:47 PM by JAP
		SHOT CLASSIFIER AND IN PROCESS SHOT SIZE TEST by donhan 10/26/20 02:11 PM Dave Barkley Replies: 7 Views: 16,840	7	16,840	10/26/20 02:11 PM by Dave Barkley
		Intensity limits using glass bead media by Steve Botson 04/08/20 03:56 PM Steve Botson Replies: 0 Views: 3,079	0	3,079	04/08/20 03:56 PM by Steve Botson
		Fatigue testing results by Steve Botson 01/23/20 08:21 PM Jack Champaigne Replies: 5 Views: 13,125	5	13,125	01/23/20 08:21 PM by Jack Champaigne
		Media Shot Shape Requirements by Rich 05/09/19 03:10 PM Rich Replies: 2 Views: 7,727	2	7,727	05/09/19 03:10 PM by Rich
		Sieve Analysis by Rich 05/07/19 09:09 PM Walter Replies: 3 Views: 8,715	3	8,715	05/07/19 09:09 PM by Walter
		Need supplier chrome steel balls for peenforming by Jack Champaigne 02/06/19 02:38 PM Jack Champaigne Replies: 0 Views: 2,883	0	2,883	02/06/19 02:38 PM by Jack Champaigne
		Ams 2431/4c Alternative media options by tec 07/17/18 06:59 PM tec Replies: 0 Views: 3,416	0	3,416	07/17/18 06:59 PM by tec
		Cut wire media inspection SAE ASEC discussion by Jack Champaigne 03/09/18 09:03 PM Socrates Replies: 2 Views: 10,663	2	10,663	03/09/18 09:03 PM by Socrates
		Shot Peen Dust Recycling by cmayleben 03/08/18 09:54 PM Walter Replies: 4 Views: 20,293	4	20,293	03/08/18 09:54 PM by Walter

Moderated by: Andy Levers, Dave Barkley, Dennis Scharer, Jack Champaigne, Jeff Derda, John Cammett, Kumar Balan, Socrates, Walter

Page 1 of 4

1

2

3

4

Sponsored by Electronics Inc. © 2026 Electronics Inc. All Rights Reserved.

Powered by UBB.threads™ PHP Forum Software 7.7.5