The knowledge base for the shot peening and blast cleaning industries
Specifications Relating to Shot Peening
The articles below are archived in the shotpeener.com Library. Click on an article title below to view details and access a free full text pdf.
Abstracts of many shot peening specifications are listed in this database, however, the full text document must be purchased from the copyright owner (SAE, ASTM, etc.)
Total articles (180)
Page 8 of 13
- Military Standard Abrasive Blasting
- Year: 1989, Source: MIL-STD-1504B (Superseding MIL-STD-1504A Aug. 23, 1978)
- SCOPE: This standard covers the process and materials required for abrasive blasting of aircraft and missiles components....
- Shot Peening of Metal Parts
- Year: 1989, Source: MIL-S-13165C
- This specification is approved for use by all Departments and Agencies of the Department of Defense. 7-June-1989 superseding MIL-S-13165B 31-Dec-1966 ...
- Steel Grit, Shot, And Cut Wire Shot; And Iron Grit And Shot-blast Cleaning And Peening
- Year: 1989, Source: MIL-S-851D 21 April 1989
- This specification covers cast iron or hardened cast steel grit and shot for blast cleaning of castings, forgings, ship hulls and decks, or other parts prior to use for the removal of sand, slag, rust...
- Cast Steel Grit, Proposed Specification
- Year: 1989, Source: SAE: J 1993
- This SAE recommended practice describes the chemical composition, and physical characteristic requirements for high carbon cast steel grit, to be used for blast cleaning and etching operations....
- Glass Bead Peening Procedures
- Year: 1988, Source: US Government MIL-STD-852 Notice 1
- MIL-STD-852, dated 21 Sep 1965, has been reviewed and determined to be valid for use in acquisition. ...
- Calibration Systems Requirements
- Year: 1988, Source: MIL-STD-45662A
- This military standard contains requirements for the establishment and maintenance of a calibration ayatem used to control the accuracy of measuring and test equipment (M&TE) and measurement standards...
- Steel Shot - Commercial Item Description
- Year: 1988, Source: A-A-1042B
- This commercial item description covers hardened steel shot for general blasting and peening purposes. (The General Services Administration has authorized the use of this commercial item description i...
- Commercial Item Description Steel Shot
- Year: 1989, Source: A-A-1042B
- THE GENERAL SERVICES ADMINISTRATION HAS AUTHORIZED THE USE OF THIS COMMERCIAL ITEM DESCRIPTION IN LIEU OF MILITARY SPECIFICATION MIL-S-851C. This commercial item description covers hardened steel sho...
- Calibration Systems Requirements
- Year: 1988, Source: MIL-STD 45662A
- 1 August 1988 This military standard contains requirements for the establishment and maintenance of a calibration system used to control the accuracy of measuring and test equipment (M&TE) and measur...
- Size Classification And Characteristics Of Glass Beads For Peening
- Year: 1988, Source: SAE: J 1173 Sep88
- This specification covers the characteristics of glass beads used for peening, and provides for standard glass bead size numbers. The glass bead classification number is the approximate nominal diame...
- Shot Peening AMS 2430 K
- Year: 1988, Source: SAE: AMS 2430 K Rev. 04/1988
- This specification covers the engineering requirements for peening surfaces of parts by impingement of metallic shot, glass beads, and ceramic shot. To induce residual compressive stress in surface ...
- Plastic Media, For Removal Of Organic Coatings
- Year: 1988, Source: MIL-P-85891(AS) 6 May 1988
- This specification covers five types of plastic media used for removal of organic coatings in an abrasive blast operation: (I) Polyester (Thermoset); (II) Urea Formaldehyde (Thermoset); (III) Melamin...
- Peening Media Glass Shot AMS 2431 6
- Year: 1988, Source: SAE: AMS 2431/6, REV 04/l0/1988
- This specification, in conjunction with the general requirements covered in AMS 2431 established the requirements for glass shot to be used for peening of metal parts. Descriptors: Quality controls a...
- Peening Media General Requirements AMS 2431
- Year: 1988, Source: SAE: AMS 2431, REV 04/l/1988
- This specification establishes general requirements for the media to be used in controlled shot peening of metal parts. Reference to AMS 2431 with appropriate slash number on a purchase order consti...
The Shot Peener magazine is dedicated to sharing information and expanding global markets for the shot peening and blast cleaning industries. We cover topics of importance to a wide range of readers -- from OEMs to engineers to academics to machine operators -- in a fresh and engaging format. The magazine is free of charge to make it accesssible to as large an audience as possible.
Electronics Inc. publishes the magazine. For more information, visit The Shot Peener magazine.