The knowledge base for the shot peening and blast cleaning industries
Specifications Relating to Shot Peening
The articles below are archived in the shotpeener.com Library. Click on an article title below to view details and access a free full text pdf.
Abstracts of many shot peening specifications are listed in this database, however, the full text document must be purchased from the copyright owner (SAE, ASTM, etc.)
Total articles (180)
Page 9 of 13
- Peening Media Conditioned Stainless Steel Cut Wire Shot AMS 2431 4
- Year: 1988, Source: SAE: AMS 2431/4, REV 04/01/1988
- This specification, in conjunction with the general requirements covered in AMS 2431, establishes the requirements for conditioned stainless steel cut wire shot to be used for peening of metal parts. ...
- Peening Media Conditioned Carbon Steel Cut Wire Shot AMS 2431 3
- Year: 1988, Source: SAE: AMS 2431/3, REV 04/01/1988
- This specification, in conjunction with the general requirements covered in AMS 2431, establishes the requirements for conditioned carbon steel cut wire shot to be used for peening of metal parts....
- Peening Media Ceramic Shot AMS 2431 7
- Year: 1988, Source: SAE: AMS 2431/7, REV 04/01/1988
- This specification, in conjunction with the general requirements covered in AMS 2431, establishes the requirements for ceramic shot, for peening of metal parts. Descriptors: Quality controls and proc...
- Peening Media Cast Steel Shot, Hard (55 - 62 Hrc) AMS 2431 2
- Year: 1988, Source: SAE: AMS 2431/2, REV 04/0l/1988
- This specification, in conjunction with the general requirements covered in AMS 2431, establishes the requirements for hard cast steel shot to be used for peening of metal parts. Descriptors: Quality...
- Peening Media Cast Steel Shot, Regular (45 - 52 Hrc) AMS 2431 1
- Year: 1988, Source: SAE: AMS 2431/1, REV 04/0l/1988
- This specification, in conjunction with the general requirements covered in AMS 2431, establishes the requirements for regular cast steel shot to be used for peening of metal parts. Descriptors: Qual...
- Peening Media Case Hardened Steel Peening Balls AMS 2431 5
- Year: 1988, Source: SAE: AMS 2431/5, REV 04/01/1988
- This specification, in conjunction with the general requirements covered in AMS 2431, establishes the requirements for peening balls to be used for peening of metal parts. Descriptors: Quality contro...
- Aluminum Alloy Sheet And Plate 1.0mg-0.60si-0.28cu-0.20cr(6061;-t6 Sht,-t651 Plate) Solution And Precipitation Heat Treated
- Year: 1988, Source: SAE: AMS 4027K
- This specificationcovers an aluminum alloy in the form of sheet and plate. Primarily applicable for parts where strength is required and limited formability is acceptable....
- Balls, Bearing, Ferrous and Non-Ferrous (for use in Bearings, Valves and Bearing Applications) General Specification for
- Year: 1987, Source: MIL-B-1083D 16 OCT 87
- This specification is approved for use by all departments and agencies of the Department of Defense. This specification covers requirements for ferrous and non-ferrous inch balls....
- Standard Specification For Wire-cloth Sieves For Testing Purposes
- Year: 1987, Source: ASTM: E 11-87
- This specification covers the design and construction of sieves wherein a screening medium of woven wire cloth is mounted in a frame for use for precision testing in the classification of materials ac...
- Peening Of Metal Parts Local Process Specification (lps/jx 341-149-87)
- Year: 1987, Source: LPS/JX 341-149-87
- This specification establishes the materials, equipment, procedures and requirements applicable to metallic shot and glass bead saturation peening and peen forming of aircraft parts and assemblies....
- Japan's Launch Vehicle Program Update
- Year: 1987, Source: SAE: 871340
- National Space Development Agency of Japan, NASDA, as an implementing agency in Japan for space applications missions, has successfully developed N series program, so called N-I and N-II vehicles, and...
- Cut Wire Shot
- Year: 1987, Source: SAE: J 441 May87
- Cut wire shot shall be the product of carbon steel wire or stainless wire Type 302, 304 Condition B, spring Temper, cut into the form of cylinders with length approximately equal to the wire diameter....
- Case History Of Dry Paint Stripping
- Year: 1987, Source: SAE: 870754
- The purpose of this paper is to present an overview of the use of the dry paint stripping process in the aircraft industry. It spotlights the major influencing factors of three current users in diffe...
- Peening of Metals MIL-P-81985 Amendment 1
- Year: 1984, Source: US Government Spec
- This amendment forms a part of Military Specification MIL-P-81985(AS) dated 18 October 1974, and is approved for use by the Naval Air Systems Command, Department of the Navy and is available for use b...
The Shot Peener magazine is dedicated to sharing information and expanding global markets for the shot peening and blast cleaning industries. We cover topics of importance to a wide range of readers -- from OEMs to engineers to academics to machine operators -- in a fresh and engaging format. The magazine is free of charge to make it accesssible to as large an audience as possible.
Electronics Inc. publishes the magazine. For more information, visit The Shot Peener magazine.